1  設備結構
1  Device Structure
    該打磨設備采用1.2mm厚鍍鋅板翻邊、組合式裝配結構,外形美觀,經濟而用,更便于運輸與組裝,濾筒才用直接有卡盤卡在多孔板上,便于用戶檢修和更換濾筒,使濾筒不易磨損而且有助于清灰;濾料根據用戶的實際需要進行選擇。
       With 1.2mm thick galvanized sheet flanging, combined assembly structure, beautiful appearance, economic and durable, more convenient for transportation and assembly. The filter cylinder is directly mounted on the porous plate with a chuck, which is convenient for the user to repair and replace the filter cylinder, making the filter cylinder not easy to wear out and helpful for ash removal. The filter material is selected according to the actual needs of the user.
1.2  工作原理
1.2   Working Principles:
        本設備采用負壓式設計,即含塵氣體由進風口進入下箱體,通過濾簡進行過濾,由于濾筒的各種效應作用將粉塵、氣體分離開。粉塵被吸附在濾筒上,而氣體穿過濾筒由文氏管進入上箱體,凈化后的空氣可以直接通過除塵器的回風口排出,完成整個系統的循環。含塵氣體通過濾簡凈化的過程中,隨著時間的增加,積聚在濾筒上的粉塵越來越多,因而使濾筒的阻力逐漸增加,通過濾簡的氣體量逐漸減少,為了使除塵器能正常工作,設備安裝了脈沖自控清理裝置,是由脈沖控制儀發出指令按順序觸發每個控制閥,開啟脈沖閥,使氣包內的壓縮空氣由噴吹管經各孔文氏管噴射到各對應的濾筒內,濾筒在氣流瞬間反向作用下急劇膨脹,使積在濾簡表面的粉塵脫落，濾筒得到再生,被清掉粉塵的粉塵落入灰斗?；叶凡捎猛评浇Y構,清灰過程快捷方便。上部設有卸灰板,******灰塵全部集中到灰斗。
1.2  工作原理
1.2   Working Principles:
      This equipment adopts the negative pressure design, that is, the dust gas enters the lower box through the air inlet and filters through the filter cylinder. Due to various effects of the filter cylinder, the dust and gas are separated. The dust is adsorbed on the filter cylinder, and the gas passes through the filter cylinder and enters the upper tank through the venturi tube. The purified air can be discharged directly through the return air port of the dust collector to complete the circulation of the whole system. Cartridge dust gas through the process of purification, with the increase of time, more and more dust accumulated on the cartridge, therefore make the resistance of the filter cartridge gradually increase, the amount of gas through the filter cartridge gradually reduce, in order to make the filter can work properly, installation of equipment of pulse cleaning device, is controlled by pulse instrument issued instructions in order to trigger each control valve, open the pulse valve, gets compressed air bags made by spray torch through each Kong Wenshi tube into the corresponding filter cartridge, cartridge under the effect of instant air reverse swelling, make the dust accumulated on the surface of the filter cartridge, fall off, get renewable cartridge, clear out dust particles of dust fall into ash hopper. Ash bucket adopts push-pull structure, the process of ash removal is quick and convenient. The upper part is provided with ash discharge board to ensure that all dust is concentrated in the dust hopper
1.3  結構特點
1.3  Structural Characteristics:
        設備出廠前已經過整體的裝機試機,采用內循環方式,與傳統的除塵器相比沒有復雜的管道,安裝時候設備擺放到位,只需稍微的檢查和調試即可投入使用。由于沒有排風管道,節省安裝空間。
        1. 高適用性設計,除塵器可適應含塵氣體性質的大范圍波動,井可根據用戶情況做適應性非標設計
        2. 特殊的結構設計加上嚴格的濾料及零部件選用,可滿足極為嚴格的環保要求,除塵器的排放可確保低于
        3.優化的進出風道設計,內部設置了氣流均布裝置,有利于均勻的氣流分布;
        4. 防漏風設計,******除塵器的漏風率降至******；
        5.全鋼分體結構設計,便于設備的運輸及安裝,并******設備的制造精度；
        6.分室脈沖清灰技術,************的清灰強度及效果;
        7.除塵器停機自清系統,確保除塵器始終處于******工作狀態;
        8.獨有的非線性均流靜壓噴管,確保噴吹均勻;
        9.口長壽命設計,主體設備按照使用壽命10年以上進行設計制造;
       10.低運行費用,優化的工藝參數設計,有利于除塵器低阻高效穩定運行,降低系統能耗,同時有效減輕了濾料的損耗及維護工作;
       11.采用高品質零部件,提高設備運行******性,減少維護工作;
       12.全部采用高品質的濾料及附件,濾芯平均壽命一般超過60個月;
       13.特殊灰斗設計,粉塵卸出無障礙
1.3   結構特點
1.3  Structural Characteristics:
 Before leaving factory, the equipment has been installed and tested as a whole. It adopts internal circulation mode and has no complicated pipelines compared with the traditional dust remover. The equipment is installed
       Put in place, only a little inspection and debugging can be put into use. As there is no exhaust duct, installation space is saved.
1.High applicability design, dust collector can adapt to the nature of dust and gas in a wide range of fluctuations, and according to the user's situation to do adaptive non-standard design;
2.The special structure design and strict selection of filter materials and parts can meet the extremely strict environmental protection requirements. The discharge of the dust collector can be guaranteed to be less than 50mg/m3
3. Optimized design of inlet and outlet air duct, with airflow distributing device inside, which is conducive to uniform airflow distribution;
4. Air leakage prevention design, to ensure the dust collector's air leakage rate to the minimum;
5. All steel split structure design, easy to transport and install the equipment, and ensure the manufacturing accuracy of the equipment
6. Compartment pulse ash removal technology to ensure the best ash removal intensity and effect;
7. The shutdown self-cleaning system of the dust remover ensures that the dust remover is always in the best working condition
8. Unique nonlinear equal-flow static pressure nozzle ensures even injection
9. Long life design. The main equipment shall be designed and manufactured according to the service life of more than 10 years
10. The low operating cost and optimized process parameter design are conducive to the low resistance, high efficiency and stable operation of the dust collector, as well as the reduction of system energy consumption. Reduce the loss of filter material and maintenance11. Adopt high-quality parts to improve the reliability of equipment operation and reduce maintenance
12. All filter materials and accessories are of high quality. The average life of filter elements generally exceeds 60 months
13. Special design of ash hopper makes the dust discharge barrier-free